Getting Started PTB - Revision history

Vei046: Updated release version

2020-05-14T09:50:48Z

Updated release version

← Older revision		Revision as of 09:50, 14 May 2020
Line 20:		Line 20:
	1. Fetch changes from [https://git.app.uib.no/pct/wp3\|wp3 upstream repo]		1. Fetch changes from [https://git.app.uib.no/pct/wp3\|wp3 upstream repo]

	2. Checkout tag of your select release. See [https://git.app.uib.no/pct/wp3/-/releases\|latest releases]. This guide ~~assumesPTB~~-~~v2.0~~.		2. Checkout tag of your select release. See [https://git.app.uib.no/pct/wp3/-/releases\|latest releases]. This guide assumes PTB-v3.1-beta3

	<syntaxhighlight lang="bash">		<syntaxhighlight lang="bash">
	$ git checkout PTB-v2.0		$ git checkout PTB-v3.1-beta3
	</syntaxhighlight>		</syntaxhighlight>

Line 31:		Line 31:

	<syntaxhighlight lang="bash">		<syntaxhighlight lang="bash">
	$ make get_latest_bitstream TAG=PTB-v2.0		$ make get_latest_bitstream TAG=PTB-v3.1-beta3
	</syntaxhighlight>		</syntaxhighlight>

Ogr043: /* Superfast flow */

2019-09-13T08:04:18Z

Superfast flow

← Older revision		Revision as of 08:04, 13 September 2019
Line 4:		Line 4:
	By checking the serial debug output, one can check if the correct version is running.		By checking the serial debug output, one can check if the correct version is running.

	1. (Optional) ~~Open a new terminal window and start~~ debugging stream. Shows messages from embedded system once programmed.		1. (Optional) Start debugging stream. Shows messages from embedded system once programmed.

	2. [[Media:power_on_board_ptb.jpg \| Power on board]]		2. [[Media:power_on_board_ptb.jpg \| Power on board]]
Line 15:		Line 15:
	$ make serial		$ make serial
	</syntaxhighlight>		</syntaxhighlight>

	== Getting Started ==		== Getting Started ==

Ogr043 at 08:03, 13 September 2019

2019-09-13T08:03:55Z

← Older revision		Revision as of 08:03, 13 September 2019
Line 1:		Line 1:
			== Superfast flow ==

			The PTB stores the bitstream, embedded software and a bootloader on a flash memory. A power cycle will not reset this. Thus, one can use the PTB by simply turning in on.
			By checking the serial debug output, one can check if the correct version is running.

			1. (Optional) Open a new terminal window and start debugging stream. Shows messages from embedded system once programmed.

			2. [[Media:power_on_board_ptb.jpg \| Power on board]]

			The serial debug window should have something like the following output:

			[[File:PTB-boot.png\|400 px]]

			<syntaxhighlight lang="bash">
			$ make serial
			</syntaxhighlight>
	== Getting Started ==		== Getting Started ==

Ogr043 at 08:00, 13 September 2019

2019-09-13T08:00:55Z

← Older revision		Revision as of 08:00, 13 September 2019
Line 38:		Line 38:
	</syntaxhighlight>		</syntaxhighlight>

	9. [[Media:~~reset_ptb_hard~~.jpg \| Restart PTB]]		9. [[Media:reset_ptb.jpg \| Restart PTB]]

	The serial debug window should have something like the following output:		The serial debug window should have something like the following output:

	[[File:PTB-boot.png\|400 px]]		[[File:PTB-boot.png\|400 px]]

Ogr043 at 08:00, 13 September 2019

2019-09-13T08:00:07Z

← Older revision		Revision as of 08:00, 13 September 2019
Line 38:		Line 38:
	</syntaxhighlight>		</syntaxhighlight>

	9. [[Media:~~restart_ptb~~.jpg \| Restart PTB]]		9. [[Media:reset_ptb_hard.jpg \| Restart PTB]]

	The serial debug window should have something like the following output:		The serial debug window should have something like the following output:

	[[File:PTB-boot.png\|400 px]]		[[File:PTB-boot.png\|400 px]]

Ogr043 at 07:56, 13 September 2019

2019-09-13T07:56:50Z

← Older revision		Revision as of 07:56, 13 September 2019
Line 32:		Line 32:

	8. Generate bootloader and program flash		8. Generate bootloader and program flash

			<syntaxhighlight lang="bash">
			$ make gen_bootimage
			$ make program_flash
			</syntaxhighlight>

	9. [[Media:restart_ptb.jpg \| Restart PTB]]		9. [[Media:restart_ptb.jpg \| Restart PTB]]

Ogr043: Created page with "== Getting Started == 1. Fetch changes from [https://git.app.uib.no/pct/wp3|wp3 upstream repo] 2. Checkout tag of your select release. See [https://git.app.uib.no/pct/wp3/-..."

2019-09-13T07:56:23Z

Created page with "== Getting Started == 1. Fetch changes from [https://git.app.uib.no/pct/wp3|wp3 upstream repo] 2. Checkout tag of your select release. See [https://git.app.uib.no/pct/wp3/-..."

New page

== Getting Started ==

1. Fetch changes from [https://git.app.uib.no/pct/wp3|wp3 upstream repo]

2. Checkout tag of your select release. See [https://git.app.uib.no/pct/wp3/-/releases|latest releases]. This guide assumesPTB-v2.0.

<syntaxhighlight lang="bash">
$ git checkout PTB-v2.0
</syntaxhighlight>

3. Make sure repo is clean

4. Get pre-built bitstream.

<syntaxhighlight lang="bash">
$ make get_latest_bitstream TAG=PTB-v2.0
</syntaxhighlight>

5. Build embedded software

<syntaxhighlight lang="bash">
$ make sdk_gen_projects PRJ=PTB
</syntaxhighlight>

6. (Optional) Open a new terminal window and start debugging stream. Shows messages from embedded system once programmed.

<syntaxhighlight lang="bash">
$ make serial
</syntaxhighlight>

7. [[Media:power_on_board_ptb.jpg | Power on board]]

8. Generate bootloader and program flash

9. [[Media:restart_ptb.jpg | Restart PTB]]

The serial debug window should have something like the following output:

[[File:PTB-boot.png|400 px]]